Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

了一种无氰的高硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高的中小截面重要球铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，铸造大断面高韧性球铁冷却壁，成功地获得了铸件中心部位铸态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提高了清砂质量及效率,进一步改善了铸件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的铸件表面无缺，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了种无氰的高硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量求高的中小截面铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基稀土镁复合化剂，铸造大断面高韧性铁冷却壁，成功地获得了铸件中心部位铸态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的造,增加抛丸头,提高了清砂质量及效率,进善了铸件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的高硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高的中小截面重要球铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，铸造大断面高韧性球铁冷却壁，成功地获得了铸件中心部位铸态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提高了清砂质量及效率,进一步改善了铸件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰高硅铝铸件浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高中小截面重要球铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，铸造大断面高韧性球铁冷却壁，成功地获得了铸件中心部位铸态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室改造,增加抛丸头,提高了清砂质量及效率,进一步改善了铸件外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦度,减少破碎是降低铸件废品率,减少原料消耗关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出耐火材料所组成涂料在高温急热时不开裂，浇注出铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是炉炉门件常见陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的高硅铝件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高的中小截面重要球铁件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，大断面高韧性球铁冷却壁，成功地获得了件中心部位态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改,增加抛丸头,提高了清砂质量及效率,进一步改善了件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出件，解决了轴套件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保的块状度,减少破碎是降低件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 件取样位置不同时，由于浇凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的件表面无陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门件常见造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究一种无氰的高硅件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高的中小截面重要球铁件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，造大断面高韧性球铁冷却壁，成功地获得件中心部位态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提高清砂质量及效率,进一步改善件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出件，轴套件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 件取样位置不同时，由于浇凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的高硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在要求高的中小截面重要球铁铸件上。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

钇基重稀土镁复合球化剂，铸造大断面高韧性球铁冷却壁，成功地获得了铸件中心部位铸态高性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提高了清及效率,进一步改善了铸件的外观。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求的中小截面重要球铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，铸造大断面韧性球铁冷却壁，成功地获得了铸件中心部位铸态性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸,了清砂质量及效率,进一步改善了铸件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的高硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在质量要求高的中小截面重要铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁化剂，铸造大断面高铁冷却壁，成功地获得了铸件中心部位铸态高能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提高了清砂质量及效率,进一步改善了铸件的外观质量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在高温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。

Misrun is the common defects found in oven door castings process.

浇不足是焦炉炉门铸件常见铸造缺陷。

A new non-cyanide zinking process for high-Si aluminum cast has been studied in this paper.

研究了一种无氰的硅铝铸件的浸锌新工艺。

The mixed nodulizer can be applied for the key middle and small section casts of ductile iron.

可以在量的中小截面重球铁铸件上应用。

Gas Engine Block, Engine Head, Bearing Cap, Turbo-charge Housing, Manifold Exhaust, Diesel Engine Parts, Slotware.

产品/Product：汽车发动机缸体、缸盖、轴承盖、涡轮增压器壳体、排汽歧管、柴油发动机铸件、槽盘。

The RE(Y)-Mg-Si-Fe nodularizer had been used to cast heavy sectioned high ductile nodular iron cooling wall castings.

应用钇基重稀土镁复合球化剂，铸造大断面韧性球铁冷却壁，成功地获得了铸件中心部位铸态性能。

Through altering the Q365 shot blasting house,abrator head can raise the quality of sand cleaning,and improve the appearance of casting.

通过对Q365抛丸清理室的改造,增加抛丸头,提了清砂量及效率,进一步改善了铸件的量。

A three-legged ejector sleeve is adopted in the die casting mould to take cast stripping mould, the problem that the cast difficultly demould is solved.

采用三脚推管推出铸件，解决了轴套铸件脱模难的问题。

To keep its lumpiness and reduce the number of broken product seems a key step for the decrease of rejection ratio and raw material consumption.

保持型焦的块状度,减少破碎是降低铸件废品率,减少原料消耗的关键。

Microstructure analysis showed significantly consistent change in nodule counts and possibly the numbers of microshrinkage pores present from the bottom to the top of heavy-section casting.

在断面 铸件取样位置不同时，由于浇铸凝固时间不同，疲劳强度也不同。

The coatings composed by the chosen refractory is crackfree in high temperature.The castings using the coatings is free of surface defect and the surface roughness can reach 18 - S.

根据此法选出的耐火材料所组成的涂料在温急热时不开裂，浇注出的铸件表面无缺陷，表面粗糙度达18-S。