A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(烧温度、烧结温度保温时间、降温方式)理工艺进行研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新工艺制取的硬质合金刀片进行切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 : 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构的分析,结合计算机图形理软件计算出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

矿冶共晶工程烧结车间的电气设计,并阐述设计遇到一些问题以解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究烧结工艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度的影响,观察并分析断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂配料系统中采用核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构的分析,结合计算机图形处理软件计算出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶程烧结车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到处理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理工艺进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

烧结碳化新工艺制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过焊缝金相显微结构的分析,结合机图形处理软件出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶工程烧结车间的电气设,并阐述了设遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到处理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结工艺参数金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧制了一种新型的生灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温度、烧温度及保温时间、降温方式)及预处工艺进行了究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧碳化新工艺制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微构的分析,合计算机图形处软件计算出焊缝的烧密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶工程烧车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧过程中添加部分矿,以补充碱的消耗,同时达到处的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

究了烧工艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片合强度的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打、烧不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在钢烧预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧矿中铁氧化物均以赤铁矿、磁铁矿为主，粘相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理工艺了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新工艺制取的硬质合金刀了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金结构的分析,结合计算机图形处理软件计算出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶工程烧结车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到处理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结工艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦结合强度的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法后再经高温烧结制。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧过程(预烧温度、烧结温度及保温时间、降温式)及预处理工艺进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新工艺制取硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构分析,结合计算机图形处理软件计算出焊缝烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶工程烧结车间电气设计,并阐述了设计遇到一些问题以及解决法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱消耗,同时达到处理霞石目。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结工艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打结、烧结不好炉衬造严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质钙质、铝质原材料按适当比例配合，经后烧结至部分熔融而制。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理工艺进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新工艺制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构的分析,结合计算机图形处理软件计算出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶工程烧结车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中分霞石矿,以补充碱的消耗,同时达到处理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结工艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停工时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种型的生石灰消器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理艺进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳艺制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 介: 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构的分析,结合计算处理软件计算出焊缝的烧结密度。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

介绍了矿冶共晶程烧结车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到处理霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结艺参数对金属陶瓷摩擦材料抗剪强度和金属陶瓷摩擦片结合强度的影响,观察并分析了断口貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。

A new type of burnt lime slaker have been developed by LAIGANG sintering plant.

莱钢烧结厂研制了一种新型的生石灰消化器。

Made of shaping Polytetrafluorethylene Resin by moulding in ordinary temperature then through high heat sintering.

将聚四氟乙烯树脂在常温下用模压法成型后再经高温烧结制成。

The process conditions,including presintering temperature,sintering temperature and time,cooling mode and pretreatment were studied.

对烧成过程(预烧温、烧结温及保温时间、降温方式)及预艺进行了研究。

This paper describes the cutting test of hard alloy tip produced by using the new carbusintering technique.

对采用烧结碳化新艺制取的硬质合金刀片进行了切削试验。

Sinter type fastigiate-handle drills:Use for drilling hard and brickle material,...

简 : 烧结锥柄钻头：适用于玻璃、陶瓷等硬性材料的钻孔。

A white powder,coarse particles and mealiness ,hardly souble in acidic or alkaline solutions,with stable chemical property and good sintering performance.

外观呈白色粗颗或微粉状两种，难溶于酸或碱液中，化学性能稳定，具有良好的烧结性能。

The effects of carbonous density and solid volume loading on the microstructures, and the performance of the new method were investigated.

通过对焊缝金相显微结构的分析,结合计算机图形软件计算出焊缝的烧结。

The author introducd the electric equipment design of ore smelting eutecticum engineering of ore sintering plate, stated the problemes and the countermeasures.

绍了矿冶共晶程烧结车间的电气设计,并阐述了设计遇到一些问题以及解决的方法。

Addition of partial nephelite during bauxite sintering could not only make up consumption of soda, but also attain purpose for treating nephelite.

在铝土矿烧结过程中添加部分霞石矿,以补充碱的消耗,同时达到霞石的目的。

The effects of sintering parameters on the shear and bond strength of ceramet friction material were studied and its fracture morphology was observed and analyzed.

研究了烧结艺参数对金属陶瓷摩擦材料抗剪强和金属陶瓷摩擦片结合强的影响,观察并分析了断口形貌。

The application of magnesia-carbon brick brasque in 5t arc furnace can effctively reduce stop time in hot furnace, protect furnace from troubles of furnace bottom inversion.

镁碳砖炉衬在5t电弧炉上应用表明：该材料能有效地减少热停时间，杜绝由于因镁砂、卤水打结、烧结不好的炉衬造成严重翻炉底等问题。

CA Cement Clinker is a manufactured commodity which raw materials are high quality limestone and bauxite.The raw materials should be mixed according to suitable ratio to pelletize.

铝酸钙熟料是以经优质的钙质、铝质原材料按适当的比例配合，经成型后烧结至部分熔融而制成。

In Shigang Agglomerant Factory, the nucleonic belt weigher has been adopted in the system of automatic proportioning system, and the system dependability and the maintainability were improved greatly.

在石钢烧结厂预配料系统中采用了核子皮带秤,使配料系统的可靠性、可维护性大大提高。

For sinter with 25% and 50% MAC fines the iron oxides mainly consisted of hematite and magnetite, the bonding phase were mainly dicalcium silicate, glassiness, and a few amount of calcium ferrite.

配比为25%和50%的两种烧结矿中铁氧化物均以赤铁矿、磁铁矿为主，粘结相主要以铁酸钙、硅酸二钙和玻璃质为主，但铁酸钙数量不多。